Reattaching a Rearview Mirror. You'll need to park your car in a place where the temperature is somewhere between 5. If it's winter, find a heated garage to work inside. During the summer, pick a nice day, with moderate temperature and humidity.

Park in the shade, because if the glass is too hot, the adhesive will set with less strength. Rainy days will leave moisture on the glass. First, you'll need to remove the metal button from the mirror assembly. Very few (usually older) vehicles have mirrors that glue directly to the glass, but most will have a button you glue on first and then attach the mirror to. The Audi mirror we replaced here can be forced to part company with its button by removing a small piece of trim, disconnecting the electrics, and then inserting a screwdriver blade into the latch. Twist gently, and the mirror will pop off into your hand. Other vehicles may require loosening a small Allen- head setscrew.

If you’re away from home and in need of WiFi, now Facebook can help you find it. Originally only available in a few countries, the social network’s “Find WiFi.

Very important: Find some way to label the button . Mark it with a felt pen or a scratch at the very top or bottom. Don't mark the side that faces the glass, because the next thing we're going to do with the button is clean that surface down to bare metal. Also, you'll be looking at that surface from outside your car for a few years. Do you really want to see a smiley face there? A Circle Marks the Spot.

Press Release Location Release Date; U.S. Department of Transportation to reexamine civil penalty rate for Corporate Average Fuel Economy standards. All you can see in your. Amazon giveaways are always free to enter and never give your contact information to the sponsor. Most can be entered in three clicks with no typing and you will.

I realize now that the Volkswagen I bought under an oak tree in Sacramento has been here to New York City for a few months now and I haven’t written anything about it. Star Trek script at the Internet Movie Script Database.

There are probably some remnants of the glue on the windshield. Before you clean anything up, use a felt pen, grease pencil or a piece of masking tape to mark the position of the button. For reasons that are about to become obvious, mark the outside of the glass. If nothing else, there is probably a constellation of your fingerprints on the inside of the glass from adjusting the mirror in the past to guide you. If you are very short or very tall, you might want to use this opportunity to adjust the position of the mirror an inch or two vertically.

Don't forget that there might be wires to connect if you have any electrical components in the mirror. If you have trouble hanging pictures level in your living room, you might want to add a plumb line to the windshield with a spirit level so you can keep the button square. We usually just eyeball it. Cleanup on Aisle Three. Remove every last vestige of old adhesive from the button. The kit we bought had a piece of sandpaper in it for this.

If there is any adhesive left on the glass, scrape it off with a single- edge razor blade. Follow up with some solvent, such as lacquer thinner or rubbing alcohol, to remove your fingerprints from both the glass and the button.

A solvent cleans the glass and also acts as a catalyst for setting the adhesive later. Scrub the glass and the button without touching the surface with your fingers. You don't want to leave any oily fingerprints behind — they will prevent full adhesion.

Advertisement - Continue Reading Below. Ready? Car and glass at a moderate temperature? Got the button right side up? If so, open the small vial of adhesive with a razor blade and squeeze a single, generous drop out onto the face of the button. Squint, aim precisely, and press the button onto the glass. You get only one chance, so we really do mean aim precisely. Hold the button in place for 1 minute, using moderate pressure.

The directions in the kit say for 1. Similarly, the directions say you can install the mirror after only 3.

Hang 'Em High. Now it's a simple matter of reinstalling the mirror. If you have a setscrew- style attachment, it's easy. Just hold the mirror in place with one hand while you run the setscrew in with the other.

Remember, it's a setscrew — don't strip the threads by overtightening it. Use just enough torque on the wrench to keep the mirror from rattling. Our Audi was a little trickier; your vehicle may be, too.

We needed to rotate the mirror around the octagonal piece of the button to pop it on. After that, it was a simple matter to reconnect the electrical wiring harness and reinstall the small trimpiece. Unbuttoning the Button. Upgrading to a better mirror because you have flux gate compass envy? Or you wanted to recycle a mirror from another car, say, that junker rusting slowly away out by the fence line?

Then you'll need to remove the button from the glass. You might be able to shave it off with that razor blade. If it won't come off readily, here's a trick: Take a crescent wrench and . It'll pop off with a surprisingly gentle amount of force. Mark the position of the button on the outside of the windshield with a felt pen or grease pencil. Pop the button loose.

Some mirrors come off by removing a setscrew, but this one had spring- loaded fingers that had to be gently persuaded with a screwdriver. Hidden And Dangerous 2 Skin Mods For Skyrim. Clean, clean, clean the glass and button with the cleaner pad in the installation kit. A small vial of adhesive has enough glue to attach a good dozen mirrors. Don't feel compelled to use it all. Press the button onto the glass for 1 minute, then let it cure.